10 Best
Supco Programmable Thermostats
-
-
Product Highlights
- The relay can operate at voltages up to a maximum of 240v ac at, 5a or 14v dc at, 10a to power on.
- Thermostats are devices that sense the temperature of a system so that the temperature is maintained at the desired set point or near to it.
- It can control some of the power equipment through the relay.
SHOWview product -
Product Highlights
- Current temperature will be displayed on the module in degree celsius by default. when switched to a different mode, inactivity for approximately 5 seconds would lead to restoring the value of the module to the default temperature display.
- Temperature control range: -50 ~ 110 c
- Output: 1 channel relay output, capacity = 10a
- You can diy incubator machine with the help of xh-w1209 controller board and 3inch fan this is a diy kit for diying a incubator
- Package include: 1 pcs adapter, 2 pcs 3 inch fan and xh-w1209 digital thermostat module, acrylic case with 1 pair alligator clips
SHOWview product -
-
Product Highlights
- Current temperature will be displayed on the module in degree celsius by default. when switched to a different mode, inactivity for approximately 5 seconds would lead to restoring the value of the module to the default temperature display.
- You can diy incubator machine with the help of xh-w1209 controller board and 3inch fan this is a diy kit for diying a incubator
- Temperature control range: -50 ~ 110 c
- Output: 1 channel relay output, capacity = 10a
- Package include: 1 pcs adapter,3 inch fan and xh-w1209 digital thermostat module with 1 pair alligator clips
SHOWview product -
Product Highlights
- Temperature setting upper and lower limits ,simple operation, suitable for seafood machines.
- Measurement range: - 50 c- 110 c *control range: - 50 c - 110 c
- Temperature measurement, display, refrigeration, heating control.
- Easy to install
- Measuring accuracy: plus or minus 0.2 c *control precision: plus or minus 0.1 c
SHOWview product -
Product Highlights
- W1209: inbuilt embedded micro-controller | ntc temperature sensor | display current temperature | 3 digit 7 segment display || fan: noiseless | low current consumption || 12v adapter: short circuit, over voltage & over current protection | low fault rates | no minimum load | regulated center positive power supply | single output voltage | low ripple || crocodile clip: c...
- The w1209 digital temperature controller module can be used to measure and display temperature, turn any application on/off based on temperature reading. long pressing “+/-” resets all values to their default. the fan is commonly used to keep the system cool. the 12v power adapter is an industry power module that converts ac power to 12v 2a dc. crocodile clips are usefu...
- The robotbanao w1209 digital temperature controller module is a 12v temperature controller with 7-segment display. it has a 3 switch keypad for setting temperature and other parameters. the fan spins at ~2600 rpm and can move approx. 30cfm. the noise is 30.7 dba. 12v 2a power adapter takes an ac input of 100-240v and gives 12v 2a dc output. the alligator clip with male ...
- Dimensions: w1209(lxwxh):48x40x14mm | cable length:0.5 meter | measuring inputs: ntc10k | output type: 1 channel relay output || fan(lxwxh):80x80x25 mm | wire length:20cm || 12v adapter: output plug:5.5 mm dc plug | input plug:2-pin eu type || crocodile clip: cable length:200mm (20cm) | safety:color-coded insulation plastic cover on clips | no. of clips:10
- W1209: temperature control range(°c): -50 to +110 | resolution @-9.9°c to +99.9°c: 0.1°c | resolution @all temperatures: 1°c | accuracy: 0.1°c | refresh rate(s): 0.5 | supply voltage(v): 12 | capacity: 10a || fan: input voltage:12vdc | current:0.25a | wire gauge:26awg | rpm:2600rpm @12vdc | air flow:30.7 cfm || 12v adapter: input:100-240 vac 50/60hz | input voltage (v):...
SHOWview product -
Product Highlights
- Dual mode: - you can use it for heating and cooling mode both; in case of heating mode start temperature will be less than stop temperature and in case of cooling mode it will be opposite.
- Calibration: - in case you find visible temperature range not accurate then you can calibrate it yourself; press both buttons simultaneously and adjusting temperature range.
- Waterproof sensor: - in this device you get 100 cm long temperature sensor which is completely waterproof.
- Warranty: - the products come with 1 year warranty (to claim warranty contact us via call or whatsapp, number available below in 'product information' section.)
- Temperature controller: - this product is used to maintain the required temperature range by setting start and stop temperature. you can set the temperature range in between -50° to 110°c.
- Accurate: - 0.1°c accurate, this thermostat instantly disconnect or connect the load when reach the set temperature range.
SHOWview product -
-
Product Highlights
- Temperature control accuracy: 1°c . display accuracy 0.1°c. ntc25°c=10k b3435 soil 1% (1 meter long, regardless of positive or negative)
- Power supply voltage: dc 9~72v/ac 90 -250v(option). working environment: temperature: -20°c ~ 70°c, humidity: 90% rh no condensation.
- The working voltage is referenced on the product casing. measurement error ± 0. 5 deg c
- Power supply voltage: dc 9~72v/ac 90 -250v(option). working environment: temperature: -20°c ~ 70°c, humidity: 90% rh no condensation. product size: 75*85*35 (width, depth, height) mm.
SHOWview product
Coupon copied
